Micron
Send Email
Send SMS
Search

Home » Our Products » Programmers And Coverters


Programmers And Coverters

Micron is a leading supplier of various types of programmer like USV AVR Programmer, PICKI2, PICKIt3 and various types of converts like USB to TTL converter, USB to Serial Converter.

Relay Module ZMPT101B

REQUEST CALLBACK

Relay Module ZMPT101B
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

VOLTAGE SENSOR :

 Single-phase ac active output voltage transformer module and voltage sensor module

          ZMPT101B voltage sensor module is a voltage sensor made from the ZMPT101B voltage transformer. It has high accuracy, good consistency for voltage and power measurement and it can measure up to 250V AC. It is simple to use and comes with a multi turn trim potentiometer for adjusting the ADC output.

FEATURES :
•    within 250 V AC voltage can be measured.
•    onboard micro-precision voltage transformer
•    Installation : PCB mounting (Pin Length> 3mm)
•    Operating temperature    : 40ºC ~ + 70ºC


ADVANTAGES :
•    Analog output corresponding quantity can be adjusted.
•    Pcb board size: 49.5 (mm) x19.4 (mm)
•    Good consistency, for voltage and power measurement 
•    Very efficient and accuracy



Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

GUVA-S12SD 240nm-370nm UV Detection Sensor Module Light Sensor For Arduino

REQUEST CALLBACK

GUVA-S12SD 240nm-370nm UV Detection Sensor Module Light Sensor For Arduino
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Specification: Small size: 11mm*27mm Low power consumption: Supply voltage 2.5V ~ 5V, operating current is microamps Linear Good High Sensitivity High stability Detection range: 240nm-370nm Large angle: 130 degrees The Schottky type of photodiode for photoelectric mode Typical applications: UV tester, UV watch, outdoor sports equipment, mobile phones and other mobile phones


Additional Information:

  • Minimum Order Quantity: 10 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

PCF8591 Module

REQUEST CALLBACK

PCF8591 Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

his is a breakout board/Prototype Board for PCF8591 IC. The PCF8591 is a single-chip, single‑supply low‑power 8‑bit CMOS data acquisition device with four analog inputs, one analog output, and a serial I²C‑bus interface. Three address pins A0, A1, and A2 are used for programming the hardware address, allowing the use of up to eight devices connected to the I²C‑bus without additional hardware. Address, control, and data to and from the device are transferred serially via the two-line bidirectional I²C‑bus.

The functions of the device include analog input multiplexing, on-chip track and hold function, 8-bit analog‑to‑digital conversion, and an 8‑bit digital‑to‑analog conversion. The maximum conversion rate is given by the maximum speed of the I²C-bus.

PCF8591 IC Features
  1. Single power supply
  2. A PCF8591 operating voltage range of 2.5V-6V
  3. Low standby current
  4. Via I2C bus serial input/output
  5. PCF8591 by 3 hardware address pins addressing
  6. PCF8591 I2C bus speed sampling rate decided
  7. 4 analog inputs programmable single-ended or differential input
  8. Automatic incremental channel selection
  9. PCF8591 analog voltage range from VSS to VDD
  10. PCF8591 built-in track-and-hold circuit
  11. 8-bit successive approximation A / D converter
  12. 1 analog output DAC gain
Module Features
  1. The module supports external voltage input of the 4-way acquisition (voltage input range of 0-5v)
  2. The module integrated photoresistor by AD collection precise value of the ambient light intensity
  3. Module integrated thermistor by the precise value of the ambient temperature of the AD acquisition
  4. Module integrated 1 channel 0-5V voltage input acquisition (the blue potentiometer to adjust the input voltage)
  5. Modules with power indicator (for the module power supply indicator lights)
  6. Modules with DA output indicator, when the module DA output interface voltage reaches a certain value, will be lit panel the DA output indicator, the higher the voltage, the more obvious indicator brightness
  7. Module PCB size: 3.6cm x 2.3cm
  8. A standard double panel, thickness 1.6mm, nice layout, surrounded by a through-hole, aperture: 3mm, convenient fixed.

Specifications:

IC Chip

PCF8951

Operating Voltage Range

2.5V-6V

PCB Size (mm)

35×23

Shipment Weight

0.03 kg

Shipment Dimensions

8 x 7 x 3 cm



Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

PL2303 USB TTL Converter Module

REQUEST CALLBACK

PL2303 USB TTL Converter Module
  • PL2303 USB TTL Converter Module
  • PL2303 USB TTL Converter Module
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 130 / PieceGet Latest Price

Product Details:
Supports Windows98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
Size42mm X 15mm
Weight4 g

We are the leading suppliers for PL2303 USB TTL Converter Module. USB 2.0 to TTL UART 6PIN Module Serial Converter CP2102

Specifications:
  • USB to TTL Serial Converter
  • USB to TTL Adapter.
  • Use this device to connect your PC to a serial (TTL level) device.
  • Uses CP 2102 chipset and has a standard 0.1" pitch terminal strip to connect directly to UART or I/O pins for easy access to your MCU
  • USB specification 2.0 compliant with full-speed 12Mbps.
  • Standard USB type A male and TTL 6pin connector.
  • 6 pins for 3.3V, RST, TXD, RXD, GND & 5V.
  • All handshaking and modem interface signals.
  • Baud rates: 300 bps to 1.5 Mbps.
  • Byte receive buffer; 640 byte transmit buffer.
  • Hardware or X-On/X-Off handshaking supported.
  • Event character support Line break transmission.
  • USB suspend states supported via SUSPEND pins.


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

TL 866 CS Universal IC Programmer

REQUEST CALLBACK

TL 866 CS Universal IC Programmer
  • TL 866 CS Universal IC Programmer
  • TL 866 CS Universal IC Programmer
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 3,750 / PieceGet Latest Price

We are the leading suppliers for TL 866 CS/A Universal IC Programmer.

TL866 A Specifications:
  • Fully Automatic Fast Mode SPI Support
  • Support XP, Vista, Win7, Windows 8 - 32/64bit
  • USB interface for both data transfer and power supply;
  • User-Friendly Simple-To-Use fully automatic (no hardware jumpers/switch's)
  • Active Development - free life-time software upgrade/download
  • Multi-languages support Chinese, English
  • Supports thousands of popular devices (13,000 )

TL866 CS Specifications:
  • Model: AUTO ELECTRIC TL866CS
  • Material: Plastic housing
  • Fast programming speed
  • Low consumption
  • USB power supply, no external power supply needed
  • 40 pin over voltage protection; VPP, VCC class 4 over current protection
  • Wide range chipset 6000 + support, support serial series, parallel series chip thousands of species. 40/44/48 pin
  • large capacity flash
  • ICSP serial programming interface
  • Test CMOS4000 74/54 series of integrated circuit, Can positioning to gate error
  • Complete chip serial number function
  • Supports Windows 2000 / XP / 2003 / 2008 / Vista / 7 32-bit


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

Pt2272 RF Receiver Module

REQUEST CALLBACK

Pt2272 RF Receiver Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

The PT2272-M4 (Rx) receiver module is designed to be used in conjunction with the PT2262 (Tx) transmtter modules (1km and 4km models). When used together they are a set of wireless modules operating at 433MHz and utilise the the PT2262 & PT2272 remote control encoder and decoder IC's. They provide an easy way of remotely controlling up to 4 channels without the need of a microcontroller. This makes them ideal for applications such as security systems, garage door controllers, home automation, and remote control.

 

Receiver Board Parameters:

  • Working Frequency: 433MHz
  • Working Voltage: DC 5V
  • Working Current: ≤3mA (5.0V DC)
  • Modulation Mode: ASK
  • Sensitivity: -105dBm (50Ω)
  • Data Output: high level signal TTL
  • Output type: Momentary


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

1-Channel Solid-State Relay

REQUEST CALLBACK

1-Channel Solid-State Relay
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

1-Channel Solid-State Relay is some what similar to that of a mechanical relay & the difference is that, there is no moving contact in a Solid-State Relay. Here we make use of Phototrriac coupler to turn it ON and OFF. It finds its application in AC circuits as a TRIAC has got only limited aplications in DC.

Solid state relays do have several advantages over mechanical relays. One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays. Also, because there’s no moving contacts, solid state relays can be switched much faster and for much longer periods without wearing out.

Specification:
  • 1-Channel Solid-State Relay
  • Rated output load: 100V ~ 240V AC (50Hz/ 60Hz) 2A
  • Rated input voltage: 5V
  • Triggered at Low level
  • LED showing Solid-State Relay status
  • Input control signal:
    • Low Signal (Solid-State Relay ON / CLOSED)
    • High Signal (Solid-State Relay OFF / OPEN)
  • Screw terminals for better & secure connection
Dimensions:
  • Length:50mm
  • Width:60mm
  • Height:50mm



Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

Logic Programmers And Converters

REQUEST CALLBACK

Logic Programmers And Converters
  • Logic Programmers And Converters
  • Logic Programmers And Converters
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 100 / PieceGet Latest Price

Product Details:
Minimum Order Quantity1 Piece
PhaseSingle Phase
Input Voltage220 V
Current5 A
BrandMicron

We are the leading supplier ofLogic Programmers And Convertersmade available to our clients at competitive prices.

Yes! I am Interested

PICKIT2 Programmer

REQUEST CALLBACK

PICKIT2 Programmer
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 1,000 / PieceGet Latest Price

We are the leading traders for PICKIT2 Programmer. The PICkit™ 2 Development Programmer/Debugger (PG164120) is a low-cost development tool with an easy to use interface for programming and debugging Microchip’s Flash families of microcontrollers. The full featured Windows® programming interface supports baseline (PIC10F, PIC12F5xx, PIC16F5xx), midrange (PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30, dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit microcontrollers, and many Microchip Serial EEPROM products. With Microchip’s powerful MPLAB Integrated Development Environment (IDE) the PICkit™ 2 enables in-circuit debugging on most PIC® microcontrollers. In-Circuit-Debugging runs, halts and single steps the program while the PIC microcontroller is embedded in the application. When halted at a breakpoint, the file registers can be examined and modified.


Additional Information:

  • Item Code: PICKIT2
  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

MAX232 to TTL Converter

REQUEST CALLBACK

MAX232 to TTL Converter
  • MAX232 to TTL Converter
  • MAX232 to TTL Converter
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 120 / PieceGet Latest Price

Product Details:
Operating Voltage- 4.5V to 5V DC

We are the leading suppliers for MAX232 to TTL Converter. This is standard MAX232 to TTL logic level converter for communicationg between computer serial interface and microcontrollers.

Specifications:
  • Onboard data transmitter/receive indicator LEDs.
  • Easy to Use FRC interface.
  • Support all standard Baud rates


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

MAX485 to RS485 TTL Converter

REQUEST CALLBACK

MAX485 to RS485 TTL Converter
  • MAX485 to RS485 TTL Converter
  • MAX485 to RS485 TTL Converter
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 120 / PieceGet Latest Price

Product Details:
Pitch Interface2.54 mm
Voltage5 V
Size44 (mm) x14 (mm)

We are the leading suppliers for MAX485 to RS485 TTL Converter. This converter lets you send and receive data using the RS485 network from your Arduino/micro controller. Similar to Serial TTL and RS232 interfaces, the RS485 lets you transfer data between micro controllers and devices but with extra features! RS485 is an industry standard protocol for data transfer and provides numerous advantages. It lets you transfer data between up to 32 devices, through the same data line over a cable length of up to 1.2km (4000ft) with a maximum data rate of 10Mbit/s. This converter is designed for office and industrial applications (non-isolated), and provides superior characteristics/features normally found only on more expensive units

Specifications:
  • Module can send and receive data through RS485. Transceiver Facility (Automatic Switching between Transmit/Receive mode of RS485)
  • Module can be used with a optional twisted pair cable which WILL work up to 1.2 Km distance
  • Supports point-to-multipoint connections, this converter can connect up to 32 RS485 interface devices
  • On board 3 Pin 5.08 mm pitch screw terminal to facilitate RS-485 communication wiring
  • Termination Resister Jumper provides option to use in Multi Drop RS485 network.
  • Built in terminal resistor of 100R Ohm
  • Up to 32 nodes per network.
  • Ground Output is available onboard which can be used for wire shielding when using over long distances. This reduce EMI and interference on the cable
  • On-board MAX485 chip, low-power, Slew-Rate Transceiver
  • RS485 is brought out to 5.08 (mm) pitch 2P terminal for easy wiring RS-485 communication
  • Power LED Indication


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

USB TO U-ART CP2102

REQUEST CALLBACK

USB TO U-ART CP2102
  • USB TO U-ART CP2102
  • USB TO U-ART CP2102
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 200 / PieceGet Latest Price

Product Details:
Temperature Range-40 to +85
Size42mm X 15mm
Weight4 g

We are the leading suppliers for USB TO U-ART CP2102. This module can be used to upload Arduino sketches onto your Arduino loaded AVR devices over RXD, TXD & DTR/RST pins of module. High Quality USB to TTL converter, comes with a 4-pin extension cable.

Specifications:
  • Stable and reliable chipset CP2102.
  • USB specification 2.0 compliant with full-speed 12Mbps.
  • Standard USB type A male and TTL 6pin connector.
  • 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
  • All handshaking and modem interface signals.
  • Baud rates: 300 bps to 1.5 Mbps.
  • Byte receive buffer; 640 byte transmit buffer.
  • Hardware or X-On/X-Off handshaking supported.
  • Event character support Line break transmission.
  • USB suspend states supported via SUSPEND pins.


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

PIC KIT 3.5 Debugger/Programmer

REQUEST CALLBACK

PIC KIT 3.5 Debugger/Programmer
  • PIC KIT 3.5 Debugger/Programmer
  • PIC KIT 3.5 Debugger/Programmer
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 2,000 / PieceGet Latest Price

Microchip Technology PICkit™ 3 In-Circuit Debugger / Programmer (PG164130) allows debugging and programming of PIC® microcontrollers and dsPIC® digital signal controllers. The device uses the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE).
The PICkit 3 provides USB full-speed interface, real-time execution, diagnostic LEDs, read/write program and data memory of microcontroller, erase with verification, Programmer-to-Go, and freeze-peripherals at breakpoint.

Specifications:
  • USB (Full speed 12Mbits/s interface to host PC)
  • Real-time execution
  • MPLAB IDE compatible (free copy included)
  • Built-in over-voltage/short circuit monitor
  • Firmware upgradeable from PC/web download
  • Totally enclosed
  • Supports low voltage to 2.0 volts (2.0V to 6.0V range)
  • Diagnostic LEDs (power, busy, error)
  • Read/write program and data memory of microcontroller
  • Erase of program memory space with verification
  • Freeze-peripherals at breakpoint
  • Program up to 512K byte flash with the Programmer-to-Go


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

USB/ASP Progammer

REQUEST CALLBACK

USB/ASP Progammer
  • USB/ASP Progammer
  • USB/ASP Progammer
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 350 / PieceGet Latest Price

We are the leading suppliers for USB/ASP Progammer. These AVR programmers are based on Thomas Fischl's USBasp design and connect to your computer's USB port. Not only are they quite compact (70x20mm), but the design is really elegant. The USB interface is achieved by using an atmega8 processor and the rest is done in firmware.
Being an Open source hardware (OSHW) project, released under the GNU General Public License, you are free to download the schematic and firmware from Thomas's website, but then you have a chicken and egg problem. In order to load the USBASP firmware onto the atmega8 on the programmer, yes you guessed it, you need an AVR programmer. Much easier to buy one fully built and programmed..

Specifications:
  • Allows you to read or write the microcontroller EEPROM, firmware, fuse bits and lock bits
  • Support for Windows, Mac OS X and Linux (will work on Windows 8.1)
  • 5 KB/sec maximum write speed
  • Software controlled SCK option to support targets with low clock speed (< 1.5MHz)
  • 10 pin ISP interface (conforms to standard ISP 10-pin pinout)
  • The latest Window Drivers are fully signed, so you can use them on Windows Vista and above without any issues. The driver will work on both 32 and 64 bit platforms. On Linux And Mac OS X no kernel driver is required, just use AVRdude and specify the correct port.
  • The programmer will work with a wide variety of Atmel AVR microcontrollers including the Atmega8a and Atmega168a. A full list is available on the specifications tab. The programmer will also work with a variety of software including
  • AVRdude - Version 5.2 or later. AVRdude is available for many platforms.
  • Khazama AVR Programmer - An AVRdude GUI for MS Windows
  • BASCOM-AVR - Version 1.11.9.6 or later
  • eXtreme Burner - An easy to use GUI application for MS Windows.
  • Included with the programmer is a 10 pin ISP cable, as shown in the main photo. The programmer is ideal for use with our AVR development board and kits.


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

USB TO RS485

REQUEST CALLBACK

USB TO RS485
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 200 / PieceGet Latest Price

The USB-RS485 cable is a USB to RS485 levels serial UART converter cable incorporating FTDI’s FT232RQ USB to serial UART interface IC device which handles all the USB signalling and protocols. The cable provides a fast, simple way to connect devices with a RS485 interface to USB.

Specifications:
  • Any baud rate from 1200 bps to 115 kbps
  • Current: 100mA current at 5V DC taken from PC’s USB Port
  • Modes: RS-485 Half Duplex (2-wire)
  • Built in terminal resistor of 120R Ohm
  • Length of twisted pair cable maximum can be 1.2 Km (Kilometer) Maximum
  • Cable type for optimal range: Two core, Twisted Pair Shielded type, D+ and D- should be twisted with each other to get optimal range


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

8051/AVR USB ISP Programmer with ZIF

REQUEST CALLBACK

8051/AVR USB ISP Programmer with ZIF
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 250 / PieceGet Latest Price

We are the leading suppliers for 8051/AVR USB ISP Programmer with ZIF. This is start up level 8051 development board with ZIF(Zero Insertion Force) socket for easy inserting and removing microcontroller from board. This board is perfect for programming 8051 microcontroller as well as for designing and testing 8051 based projects.The board has onboard AT89S52 MCU(8K Flash Memory). Board has on board power supply circuit,RS232 port for serial communication with computer and other serial device(GPS modules, GSM Modems,RFID Reader),power status LED(RED),Reset switch, User switch, User LED(GREEN), and port extensions for all 4 ports. ISP (in-circuit programming) header port for easy programming. The board is compatible with the AT89S51/52 and the P89V51RD2 microcontrollers. The P89V51RD2 allows serial programming and can be programmed directly with this board through a serial connection without an external programmer

Specifications:
  • ZIF(Zero Insertion Force) socket for easy inserting and removing microcontroller from board
  • On-board bridge rectifier enables the board to accept both AC and DC Input voltages
  • Recommended Input Voltage: 9-12V
  • Min-Max Input Voltage: 9-18V
  • 5 mm standard DC plug-in jack for power supply
  • On-board 5V regulator (LM7805) circuit.
  • On-Board power supply on-off switch
  • Power Status LED(RED)
  • User LED(GREEN) connected to P2.0 through jumper JP3.
  • User Switch connected to P3.7 through jumper JP2.
  • On-board 11.0592 MHz crystal
  • Port extensions for all ports with detailed pin labelling for easy identification of pins
  • External pull-up resistors for Port 0
  • On-board MAX232 interface circuit for easy communication with a computer and other serial devices (GPS modules, GSM Modems, etc)
  • On-board ISP connector for loading HEX file into AT89S51/52.
  • 12V, 5V and GND bus provided for external peripheral.
  • High quality FR-4(1.6 mm) PCB
  • Four 3mm mounting hole for easy mounting


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

USB TO TTL CP2102

REQUEST CALLBACK

USB TO TTL CP2102
  • USB TO TTL CP2102
  • USB TO TTL CP2102
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 150 / PieceGet Latest Price

Product Details:
Baud Rates300 bps to 1.5 Mbps
Temperature Range-40 to +85
Size42mm X 15mm

We are the leading suppliers for USB TO TTL  CP2102. CP2102 chip is a single chip USB to UART bridge IC. It requires minimal external components. CP2102 can be used to migrate legacy serial port based devices to USB

Specifications:
  • Stable and reliable chipset CP2102.
  • USB specification 2.0 compliant with full-speed 12Mbps.
  • Standard USB type A male and TTL 6pin connector.
  • 6pins for 3.3V, RST, TXD, RXD, GND & 5V.
  • Byte receive buffer; 640 byte transmit buffer.
  • Hardware or X-On/X-Off handshaking supported.
  • Event character support Line break transmission.
  • USB suspend states supported via SUSPEND pins.


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

PH Sensor 3 In 1

REQUEST CALLBACK

PH Sensor  3 In 1
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Multifunctional: can test Moisture/Light/PH.

• Ideal and necessary tool for gardeners, vegetable and fruit growers, and all those who plant trees and grass.
• This item is a perfect tool to test the soil conditions ( Moisture/Light/PH) of fruits, flowers, vegetables, shrubs, etc. with high accuracy and easy operation. You can take good care of your plants.
• Save water, energy and keep your plants, lawn, flower in top condition.
• Measures moisture at root level.
• No battery required, simple and convenient to use.
• Simply insert the meter into the soil, switch to the setting you want to measure and read the scale.
• To avoid damaging the electrode, please clean the electrode after each use, do not use in soil with stones and insert forcibly
• Moist readings range: 0 DRY-  10 WET
• Light readings range: 0  DARK-2000 LIGHT
• PH readings range: 8  ALKALINE-  3.5  ACIDIC

• Probe length: 18cm(Approx)
• Size:26cm x 5.8cm x 3.6cm(Approx)

pH stands for potential Hydrogen, and it tells us whether a solution or substance is basic (pH above 7.0), acidic (pH below 7.0) or neutral (pH of 7.0).

Acidic solutions contain a greater concentration of Hydrogen ions (H+)
Basic solutions contain a higher concentration of Hydroxyl ions (OH-).

 


Additional Information:

  • Minimum Order Quantity: 10 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

PH Sensor Prob Board

REQUEST CALLBACK

PH Sensor Prob Board
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Feature:

The electrode is made of PH glass electrode and a silver/silver chloride reference electrode composition, the PH measuring elements which is used to measure water solution PH value.

Specification:

Module power: + 5.00V
Module size: 43 x 32mm
Measuring range: 0-14PH
Measuring temperature: 0-60 ¿¿¿
Accuracy: ± 0.1pH (25 ¿¿¿)
Response time: ≤1min
BNC connector type pH sensor
PH2.0 interface: (3-pin SMD)
Gain adjustment potentiometer
With power indicator


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

PICkit3 PIC KIT3 Debugger Programmer Emulator Controller Development Board

REQUEST CALLBACK

PICkit3 PIC KIT3 Debugger Programmer Emulator Controller Development Board
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

This is PICkit3 PIC KIT3 Debugger Programmer Emulator Controller Development board. USB connection is more stable than ICD2. Offline burning function. Develop debug programming, do product batch offline burning or make. Power supply input, the inner voltage can be controlled by MPLAB IDE directly.

PICKIT3.5, begin to support Win7 system. Full patch design, patch through the reflow soldering processing, more stable quality. PIC developing data, C language development tool manual. A lot of PIC basic experiment program code; ICD2 PICKIT3 etc application specification.

The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer’s PC using a full speed USB interface and can be connected to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).

Features :
  1. Full-speed USB support using Windows standard drivers
  2. Real-time execution
  3. Processors run at maximum speeds
  4. Built-in over-voltage/short circuit monitor
  5. Low voltage to 5V (1.8 to the 5V range)
  6. Read/write program and data memory of the microcontroller
  7. Diagnostic LEDs (power, active, status)
  8. Read/write program and data memory of the microcontroller
  9. 1Erase of all memory types (EEPROM, ID, configuration, and program) with verification
  10. Peripheral freeze at the breakpoint.
  11. Program up to 512K byte flash.


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

RS232 to TTL Serial Interface Module

REQUEST CALLBACK

RS232 to TTL Serial Interface Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

his RS232 to TTL Serial Interface Module is a board with the MAX3232 transceiver integrated circuit (IC). It facilitates serial communication between TTL and RS232 ports by providing the necessary electrical signal conversion.

These boards usually have a DB9 connector soldered at one end, and four header pins with jumper cables at the other end. The jumper cables enable the user to connect the wires to a breadboard or a microcontroller project board, whilst the DB9 connects directly to a COM port of a computer.

sPECIFICATIONS:

IC Chip

MAX3232

Operating Voltage

DC 3.3~5.5 V

Length (mm)

45

Width (mm)

32

Height (mm)

15

Weight (gm)

12

Shipment Weight

0.06 kg

Shipment Dimensions

5.5 x 4 x 2.5 cm



Additional Information:

  • Minimum Order Quantity: 10 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

RS232 To RS485 Module

REQUEST CALLBACK

RS232 To RS485 Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

Description
  • Compatible with EIA/TIA RS232 Standard and RS485 Standard
  • Transmission Rate: 300bps - 115.2K bps
  • It is passive and doesn't require external power
  • Self powered using the TX, RX or RTS, CTS signals for power
Specifications
  • Lighting & Surge Protectors
  • Working Mode: Asynchronous, Half-duplex, Differential Transmission
  • Transmission Media: Twisted Pair or Shielded Twisted Pair
  • Transmission Distance: 1200m (RS485), 5m (RS232)
  • RoHS Compliant


Additional Information:

  • Minimum Order Quantity: 10 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

FT 232 USB to TTL

REQUEST CALLBACK

FT 232 USB to TTL
  • FT 232 USB to TTL
  • FT 232 USB to TTL
Get Best Quote

Thanks for Contacting Us.

Approx. Rs 250 / PieceGet Latest Price

We are the leading suppliers for FT 232 USB to TTL. USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip

Specifications:
  • Implements full v2.0 USB protocol
  • Needs no external crystal
  • Internal EEPROM for device ID and Product Description strings
  • Royalty-Free Driver support for Windows, Linux, and Mac OSX


Additional Information:

  • Pay Mode Terms: T/T (Bank Transfer)
  • Delivery Time: 2-3 days
Yes! I am Interested

IR Proximity Module Using TSOP

REQUEST CALLBACK

IR Proximity Module Using TSOP
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

DESCRIPTION

The sensor module light is adaptable to the environment, the working voltage of 3.3 V to 5 V.
It has a pair of infrared transmitting and receiving tube, when detecting direction meet with obstacles (reflecting surface), reflected infrared receiving by the tube.

After the comparator circuit processing, green indicator will light up, at the same time the signal output interface output a digital signal (a low level signal), can be adjust the detection distance through the potentiometer knob, effective distance range 2 ~ 30 cm, easy to assemble and use. So it can be widely used in robot obstacle avoidance, obstacle avoidance car, line count, and so on many occasions

FEATURES

There is an obstacle, the green indicator light on the circuit board

Detection distance: 2 ~ 30cm

Detection angle: 35 °

Comparator chip: LM393

3mm screw holes for easy mounting



Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

PWM DC Motor Controller Module

REQUEST CALLBACK

PWM DC Motor Controller Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

PWM DC motor speed control module / gear motor controller / microcontroller development circuit DC12V 24V Product main parameters:Product model: YYB-3Input voltage: DC10V~26VControl power: up to 120W, current less than 10ASpeed range: 5%~100%Protection configuration: reverse power protection, 10A fuse, overcurrent protection, freewheeling protection using fast recovery diode FR107 Module size:Length * width * height: 50 * 44 * 28mmMounting hole spacing: 43.8*37.85mmMounting hole diameter: 3.1m


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

Range Finder TFM Mini Module

REQUEST CALLBACK

Range Finder TFM Mini Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

The TFMini is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 30 centimeters and as far as 12 meters! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target object, but what makes this sensor special is its size. Measuring only 42x15x16mm, the TFMini allows you to integrate LiDAR into applications traditionally reserved for smaller sensors such as the SHARP GP-series infrared rangefinders. The TFMini is easy to power at only 5V and easy to talk to using a 3.3V UART at 115200 baud.

This version of the TFMini comes with an easy to use bread board friendly cable. The four wires are terminated in pins making it easy to use with Arduinos and other platforms with female headers

Features:

  • Input Voltage: 5V
  • Average Power: ≤120mW
  • LED Peak Current: 800mA
  • UART TTL Voltage: 3.3V
  • Baud Rate: 115200 8N1
  • Resolution: 5mm
  • Minimum Detected Object Size at 2m: 20mm
  • Operating Wavelength: 850nm
  • Signal Acceptance Angle: 2.3°


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

TFMini Plus - Micro LiDAR Module

REQUEST CALLBACK

TFMini Plus - Micro LiDAR Module
Ask for Price

Thanks for Contacting Us.

Product Price :Get Latest Price

The TFMini Plus is a ToF (Time of Flight) LiDAR sensor capable of measuring the distance to an object as close as 10 centimeters (+/- 5cm up to 6m) and as far as 12 meters (+/-1% starting at 6m)! As with all LiDAR sensors, your effective detection distance will vary depending on lighting conditions and the reflectivity of your target object, but what makes this sensor special is its size. Measuring only 35x18.5x21mm, the TFMini Plus allows you to integrate LiDAR into applications traditionally reserved for smaller sensors.

Setting itself apart from the original TFmini, the TFmini Plus has been designed with an IP65 enclosure meaning its "Dust tight & water resistant", and also passed the vibration test of drone level, which will greatly expand its application range. The TFMini Plus is easy to power at only 5V and easy to talk to using common communication interfaces — UART, I/O and I2C

Features:

  • Operating Range - 0.1m~12m①
  • Accuracy - ±5cm@(0.1-6m), ±1%@(6m-12m)
  • Distance resolution - 5mm
  • Frame rate - 1-1000Hz(adjustable)
  • Ambient light immunity - 70klux
  • Operating temperature - -20℃~60℃
  • Enclosure rating - IP65
  • Light source - LED
  • Central wavelength - 850nm
  • FOV - 3.6°
  • Supply voltage - 5V±0.5V
  • Average current - ≤110mA
  • Power consumption - 550mW
  • Peak current - 500mA
  • Communication level - LVTTL(3.3V)
  • Material of enclosure - ABS+PC
  • Storage temperature - -20℃~75℃
  • Weight - 11g
  • Wire length - 30cm


Additional Information:

  • Minimum Order Quantity: 1 Number
  • Delivery Time: 2-3 days
Yes! I am Interested

 
X


Explore More Products

Contact via E-mail
Contact via SMS
Heena Jain (Marketing Executive)
Micron
Shop No. 29/30, 2nd Floor, Yamuna Building, Tara Temple Lane, Lamington Road, Girgaon
Mumbai - 400007, Maharashtra, India
Call Us: 
Call Response Rate: 64%
Share Us :
F G T L



Home  |   About Us   |  Our Products  |  Site Map  |   Contact Us

© Micron. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited

Micron