Relay Modules & Sensors
LEADING SUPPLIERS FOR DC-DC CONVERTER MODULEGravity Analog Turbidity Sensor
Approx. Rs 1 / NumberGet Latest Price
Description- Able to detect suspended particles in water
- Both analog and digital signal output modes
- Threshold is adjustable in digital signal mode
- Can be used in measurement of water quality in rivers and streams
The Gravity Analog Turbidity Sensor detects water quality by measuring level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. As the TTS increases, the liquid turbidity level increases.
- Operating Voltage: 5V DC
- Operating Current: 40mA (MAX)
- Wavelength: 910 nm
- Response Time: <500ms
- Insulation Resistance: 100M (Min)
- Output Method:Analog
- Analog output: 0-4.5V
- Operating Temperature: -30 ℃~80 ℃
- Storage Temperature: -10℃~80℃
- Weight: 30g
- Adapter Dimensions: 38mm*28mm*10mm/1.5inches *1.1inches*0.4inches
Additional Information:
- Minimum Order Quantity: 1 Number
- Delivery Time: 2-3 days
Hysrf 05 Ultrasonic Module
Product Price :Get Latest Price
DESCRIPTIONThe working principle of an ultrasonic sensor is simple and use high-frequency sound waves that are evaluated when the sensor received back the waves. To determine the distance between the robot and object, the sensor measure the elapsed time between sending and receiving the waves. These sensors are ideal for measurement in different environments where measurements cannot be affected by the surface, material, light, dust, or other noises. In robotics, ultrasonic sensors are used in a wide range of applications including here the measurement of distance, presence detection, or detect the position of an object.
HC-SR05provides measurement function between 3 centimeters and 4 meters. The HC-SR05 module hosts the ultrasonic transmitter, the receiver and control circuit.
Product Model | SRF-05 |
Operational Voltage | DC 5V |
Static Current | 2mA |
Working Frequency | 40Hz |
Distance Measurement Range | 3cm – 400cm |
Measurement Angle | 15° |
Measurement Accuracy | 0.3mm |
Output Voltage | H – 5V L – 0V |
FEATURES
- The module performance is stable, measure distance accurately.
- Module precision, blind spots (2cm) super close, stable ranging success of this product according to market powerful!
Additional Information:
- Minimum Order Quantity: 10 Number
- Delivery Time: 2-3 days
PCA9685 1Ch Servo Driver Arduino
Product Price :Get Latest Price
Features:This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers
Terminal block for power input (or you can use the 0.1" breakouts on the side)
Reverse polarity protection on the terminal block input
Green power-good LED
3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
"Chain-able" design
A spot to place a big capacitor on the V+ line (in case you need it)
220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
Solder jumpers for the 6 address select pins
i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
Configurable push-pull or open-drain output
Output enable pin to quickly disable all the outputs
Additional Information:
- Minimum Order Quantity: 10 Number
- Delivery Time: 2-3 days
MQ-9 SENSOR MODULE
Product Price :Get Latest Price
Feature:Suitable for home or factory gas leakage monitoring devices.
Have better sensitivity to CARBON MONOXIDE, METHANE, LIQUEFIED PETROLEUM GAS.
High quality dual-panel design, with power indicator and TTL signal output instructions.
DO switching signal (TTL) output and AO analog signal output.
TTL output valid signal is low. (When the output low signal is on, it can be directly connected micro-controller or relay module.)
Analog output voltage: the higher concentration, the higher voltage.
Four screw holes, easy positioning.
Long life and stability, quick response and resume.
Specification:
Input voltage: DC 5±0.2V
Power: 150mA
DO output: TTL digital 0 and 1 (0.1 and 5V)
AO output: 0.1-0.3V (relatively clean), the highest concentration voltage is about 4V.
Dimensions: 32(L) * 20(W) * 22(H) mm
Wire connecting method:
VCC - positive pole (5V)
GND - negative pole
DO - TTL switch signal output
AO - analog signal output
Additional Information:
- Minimum Order Quantity: 1 Number
- Delivery Time: 2-3 days
MQ-9 Only Sensor
Product Price :Get Latest Price
Product BrochureProduct Details:| Model / Part Number | MQ-9 |
| Target gases | CH4 |
| Operating Voltage | 5V |
| Operating Humidity | 0-95%RH |
| Preheat Duration | No less than 48 hours |
| Heating consumption | Less than 340mw |
| circuit voltage | 5V+-0.1 |
| Heating resistance | 33 ohm +-5% |
This Carbon Monoxide (CO) and flammable gas sensor detects the concentrations of CO and combustible gas in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of CO from 10 to 1,000 ppm and flammable gas from 100 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less than 150 mA at 5 V.
Additional Information:
- Delivery Time: 2-3 days
MQ-8,Hydrogen Sensor module
Product Price :Get Latest Price
Product BrochureProduct Details:| Model / Part Number | MQ-8 |
| Target gases | Hydrogen |
| Operating Voltage | 5V |
| Usage/ Application | used in gas leakage detecting equipment |
| Operating Humidity | 0- 95%RH |
| Preheat Duration | Over 24 hour |
| Circuit voltage | 5V+-0.1 |
| Load resistance | 10K ohm |
A sensitive material MQ-8 Hydrogen Gas Sensor Module H2 Alarm Detection use in clean air low conductivity tin oxide (SnO2). When there is the environment in which the combustible gas sensor, conductivity sensor with increasing concentration of combustible gases in air increases.
Using a simple circuit to convert the change in conductivity of the gas concentration corresponding to the output signal. MQ-8 hydrogen gas sensor of high sensitivity, the monitoring of the other hydrogen-containing gas is also very satisfactory.
This sensor can detect a wide range of hydrogen gas, city gas, in particular, is a low-cost sensor for a variety of applications.
Suitable for home or industrial hydrogen leakage monitoring devices. Can not interfere with ethanol vapor, soot, carbon monoxide, and other gases.
Features :- Using high-quality dual-panel design, with power indicator and TTL signal output instructions.
- The switching signal having a DO (TTL) output and analog output AO.
- TTL output valid signal is low. ( Low-level signal when the output light can directly connect to the microcontroller or relay module )
- The higher the voltage, the concentration of the analog output voltage is higher.
- A hydrogen gas detection with good sensitivity.
- There are four screw holes for easy positioning.
- Has a long life and reliable stability
- Rapid response and recovery characteristics
| Operating Voltage(VDC) | 5 |
| Current Consumption(mA) | 150 |
| Do output | TTL digital 0 and 1 ( 0.1 and 5V) |
| Ao output | 0.1-0 .3 V (Relative to Pollution ) |
| Dimensions in mm (LxWxH) | 32x22x20 |
| Weight (gm) | 7 |
| Shipment Weight | 0.02 kg |
| Shipment Dimensions | 5 x 5 x 4 cm |
Additional Information:
- Delivery Time: 2-3 days
Mq-6 Only Sensor
Product Price :Get Latest Price
Product BrochureProduct Details:| Model / Part Number | MQ-6 |
| Target gases | LPG, iso-butane, propane |
| Measuring Range | 200-10000 ppm |
| Operating Voltage | 5V |
| Operating Humidity | 0-95%RH |
| Preheat Duration | Over 24 hour |
| Circuit voltage | 5V+-0.1 |
| Load resistance | 20K ohm |
| Heater resistance | 33 ohm +-5% |
This is a simple-to-use liquefied petroleum gas (LPG) sensor, suitable for sensing LPG (composed of mostly propane and butane) concentrations in the air. The MQ-6 can detect gas concentrations anywhere from 200 to 10000ppm.
This sensor has a high sensitivity and fast response time. The sensor's output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
This sensor comes in a package similar to our MQ-3 alcohol sensor, and can be used with the breakout board below.
Additional Information:
- Delivery Time: 2-3 days
RCWl0516 Microwave Radar Sensor
Approx. Rs 1 / NumberGet Latest Price
This module has been designed as an alternative to the PIR motion detectors commonly used in burglar alarms. Instead of sensing changes in infrared radio emitted by a moving person this sensor uses a microwave Doppler radar to detect moving objects. It has a sensitivity range of ~7 meters. When triggered its trigger output pin will switch from (LOW) 0V to high (3.3V) for ~ 2 to 3 seconds before returning to its idle LOW state.Features:
Product code: HCSENS0040
Supply Voltage: 5V dc
Supply Current: >3mA (2.8mA typical)
Operating frequency: ~3.2GHz
Transmit power: 20mW (typical) / 30mW (max)
Size: 36mm x 17mm
Additional Information:
- Minimum Order Quantity: 1 Number
- Delivery Time: 2-3 days
MQ-7, Only Sensor
Product Price :Get Latest Price
Product BrochureProduct Details:| Model / Part Number | MQ-7 |
| Operating Voltage | 5V |
| Operating Humidity | 0- 95%RH |
| Usage/ Application | High sensitivity to carbon monoxide |
| Heating resistance | 33ohm +-5% |
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm.
This sensor has a high sensitivity and fast response time. The sensor's output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater coil with 5V, add a load resistance, and connect the output to an ADC.
This sensor comes in a package similar to our MQ-3 alcohol sensor, and can be used with the breakout board below.
Additional Information:
- Delivery Time: 2-3 days
AMS 1117 3.3V & 5V Voltage Regulator
Approx. Rs 45 / PieceGet Latest Price
Product Details:| Output Voltage | 3.3V |
| Output Current | 1A add the red 4.5V input |
| Input Voltage | 12V |
| Size | 25.5mm x 11.5mm |
We are the leading suppliers for AMS 1117 3.3V Power Supply Module. This power supply module is based on the AMS1117 3.3V regulator. It is capable of regulating a wide range of input voltage (4.0 to 12V) down to a fixed 3.3V output at up to 1A (Vin = 4.5V). Standard 0.1" header pins provide a means of connecting to its input and output terminals. These header pins have also been conveniently placed so that the module can be inserted face down into standard.
Additional Information:
- Pay Mode Terms: T/T (Bank Transfer)
- Delivery Time: 2-3 days
5V 4 Channel SSR
Approx. Rs 1 / NumberGet Latest Price
This 5V 4 Channel SSR G3MB-202P Solid State Relay Module 240V 2A Output with Resistive Fuse is based on the Omron G3MB SSR relay which can control up to 2A at 240VAC. This is a 4 Channel SSR relay module, each relay channel has 3 separate terminals, NO (Normal Open), COM (Common), NC (Normal Closed).
A Solid State Relay is similar to a mechanic relay where it can be controlled through a digital signal. Solid State Relay generates no noise and has a much longer lifespan in compared to the traditional mechanic relay.
When the input logic voltage is applied to the coil, the NC will disconnect from the COM breaking the conductivity between the two. At the same time, the NO will connect with the COM allowing conductivity between them. Depending on your wiring this will turn on or off the connected load.
Features :
- Has been assembled, and the electrical test passed.
- Led indicator for each relay.
- Use it to control various appliances and other equipment with large current.
- It can be controlled directly by Microcontroller
- Input control signal voltage:
- 0-2.5V status low level, relay OFF
- 3-5V status high level, relay ON
- Blue KF301 terminal connection control line is more convenient.
Additional Information:
- Minimum Order Quantity: 1 Number
- Delivery Time: 2-3 days
2-Channel Solid State Relay Module
Approx. Rs 1 / NumberGet Latest Price
2 channel Solid State RelayOur 2 channel solid state relay (SSR) acts like a mechanical relay. SSR allows you to control high-voltage AC loads from lower voltage DC control circuitry. Solid state relays, have several advantages over mechanical relays. One such advantage is that they can be switched by a much lower voltage and at a much lower current than most mechanical relays.
This Solid State Relay Module is based on Omron G3MB
Features- Channel: 2
- Control Voltage:5V
- Working Current:12.5mA
- Trigger Voltage???0-1.5V
- Trigger Current???2mA
- DC to 5v
- DC- to GND
- CH to Control Pin (LOW to Close Circuit)
Additional Information:
- Minimum Order Quantity: 10 Number
- Delivery Time: 2-3 days
Relay 12v Sugar Cube 10Amp& &7Amp
Approx. Rs 1 / NumberGet Latest Price
Power Relays with a coil rated voltage of 12V and SPDT contacts with a 10A & 7A raing. The relay have 5 pins, with good quality and long operational life.
Features:
- Pins: 5
- SPDT Contacts
Specifications:
- Rated Load: 10A 250VAC, 10A 30VDC,7A
- Max Switching Current: 10A
- Max Switching Voltage: 110VDC / 250VAC
- Coil power 0.45W
- Contact Arrangement: C:1 (NO/NC)
- Dimensions: 19 x 15 x 15 mm
Additional Information:
- Minimum Order Quantity: 10 Number
- Delivery Time: 2-3 days
Flex Sesnor 2.2 &4.5mm
Approx. Rs 1 / UnitGet Latest Price
A simple Flex Sensor 2.2″ – Bend Sensor with a length of 2.2″ which bends and flexes with a physical device. As the sensor is flex, the resistance across the sensor increases. A connector is 0.1″ spaced and bread board friendly. he flex sensor is a bend detecting sensor which has got numerous applications in robotics, medical and haptic technology. The resistance of these sensors changes in accordance with the bend, which can be measured using any microcontroller.| length | 2.2"&4.5' |
| Life Cycle | >1 million |
| Height | 0.43mm (0.017") |
| Flat Resistance | 10K Ohms ±30% |
| Bend Resistance | minimum 20K Ohms ±30% (@ 180° pinch bend) |
| Power Rating | 0.5 Watts continuous; 1 Watt Peak. |
Additional Information:
- Delivery Time: 2-3 days
Optical Detector / Phototransistor - QRD1114
Product Price :Get Latest Price
Product BrochurePopular Optocoupler. IR emitter and receiver in one package for close-range optical detection. Suitable for mini sumo robots and sumo robots.- This is a very popular infrared line/object sensor used in many robot designs.
- These sensors have an effective range of approximately 6mm (1/4″), which make the ideal for line detection.
Additional Information:
- Minimum Order Quantity: 1 Number
- Delivery Time: 2-3 days
Relay 24V, 5V & 6V
Product Price :Get Latest Price
We are the leading supplier for Relay Sugar cube 24V, 6V &5V.
Additional Information:
- Minimum Order Quantity: 10 Number
- Delivery Time: 2-3 days
Explore More Products
Micron
Mumbai - 400007, Maharashtra, India
© Micron. All Rights Reserved (Terms of Use)
Developed and Managed by IndiaMART InterMESH Limited